HHO Bike Schematic

Just as the video title says...

GenIV gasket update and bubbler setup

This is the latest improvement made by Smack - aka electrikride of in youtube. This is a more sounder, safer and more solid configuration.

I recomend DIYers to replicate your set up similar to this in order to have a more safer and sounder set up.

For more information about smack boosters - click below to see his site.

http://www.smacksboosters.110mb.com/

The following is an excerpt from his video script:

"To reduce foaming, I have increased the cell gap to .160". This also increases the fluid capacity of the cell which extends time between refills. The change in gap does not appear to have effected the efficiency of the cell significantly.

I also recommend using a second bubbler to prevent the possibility of pushing electrolyte into the engine's intake. This also acts to further scrub the output gas for a dryer, more pure hydroxy output."

Courtesy of www.youtube.com

Keep safe everyone.

燃費、改造スクーター、スズキベクスター125水素実験 HHO MINI CELL

燃費のもともと良いスズキベクスター125に水素燃料をプラスしてみました。
実験で走った感じはターボなしの車にターボを付けたような感じです。
中速の伸びがよくなります。高速では水素ガスが薄くなるせいか最高速は105ｋほどで す。
ガスの量はかなり少ないですが。電流が４Aでも体感できたのでこの１２５CCのスクー ター
でも問題なく使えそうです。最初はバッテリー上がりががすごく心配でしたがコンデンサ ー
を付けたり水素の電源をエンジンを切るまえにオフにすればバッテリーには影響ないよう です。
後ろの大きいタンクは冷却用です電流が３A以上になると水温が上がってしまうので必要 になります。
下にあるのがリアクターです。ステンレスプレート8枚つかつています。

Pulsing Hydrogen Fuel Cell while Charging Battery (OU)

These concepts go back to Tesla, and his concepts of his Tesla Switch. Also, Bedini uses these Bi-Filer coils with much success. These are attempts to show overunity while using PWM (pulse width modulation).

Regards, sirHOAX

TIG Welding your electrodes

If you use stainless and want to adopt a full bath system... see to it that all your joints or connections are TIG welded.

The cell being welded here is the Super 7 cell design... prototype #001.

HHO test cell

Here's Pete with his Bob boyce inspired Home made electrolytic cell made from whats available in his garage/ kitchen or stock room.

Pete is a VW enthusiast and is also an Earth Saver.

I find his video worth sharing. Personally. Watch out for his project!

His mission, to run his VW bus on straight HHO... a tall feat and worth attention.

All the best Pete and I look forward in seeing you soon!

Hydrogen Engine

This is an attempt to run an engine with pure HHO... ok, it's not an over unity project, the experimenter here only proves that engines can run on pure hydroxy gas, and that his flashback system works great!... even with lesser gas production. This is actually a very dangerous thing to do without a flashback arrester.

Starting the engine means, it has zero vacuum, therefore, free floating hydroxy gas are dangerously roaming in the air stack, and 2 stroke engines dont have valves to shut the cylinder to contain combustion 100 %. Flashbacks is so easy to occur. I have seen many accidents from this type of experiments.

I still would not recommend this unless you prime the engine with gasoline first just to establish the vacuum pulling factor for safety.

In my early days experimenting, one of my internet buddies destroyed his intake manifold in his V6 Plymouth voyager. This type of accidents can happen without vacuum... and this happens during starting or cranking up the engine with pure hydroxy gas a.k.a. HHO.

Word of Caution, There is no alternative for safety.